SSC JE 2026 Syllabus for Civil, Mechanical and Electrical: Paper-I and II exam pattern, negative marking and topic-wise syllabus as per official notice.
SSC JE 2026 Syllabus
Civil, Mechanical & Electrical – Paper-I & Paper-II Exam Pattern, Negative Marking and Topic-wise Syllabus
The SSC JE 2026 Syllabus is short on paper but deep in practice, and that catches a lot of diploma holders off guard. The Staff Selection Commission published the Junior Engineer Examination, 2026 notice on 2 September 2026, and Paper-I is already scheduled from 2 to 6 November 2026. If you are a Civil, Mechanical or Electrical aspirant from Hyderabad, Warangal, Vijayawada or Vizag, this is the page to keep open: the full exam pattern, the marking rules and the topic-wise syllabus for Paper-I and Paper-II, all taken from the official notice.
One thing worth knowing up front: the engineering questions are set at roughly diploma level for Civil, Mechanical and Electrical. So your polytechnic textbooks are still the best base. You do not need GATE-level depth, but you do need speed and clean basics.
SSC JE 2026 Exam Pattern (Paper-I & Paper-II)
The exam has two computer-based papers. Paper-I is a screening round. Paper-II is where your rank is decided.
Paper-I (Computer Based Examination)
| Subject | Questions | Marks | Time |
|---|---|---|---|
| General Intelligence & Reasoning | 50 | 50 | 2 Hours |
| General Awareness | 50 | 50 | |
| General Engineering: Part-A Civil & Structural or Part-B Electrical or Part-C Mechanical (as per your post) | 100 | 100 | |
| Total | 200 | 200 | 2 Hours |
Paper-II (Computer Based Examination)
| Subject | Questions | Marks | Time |
|---|---|---|---|
| General Engineering: Part-A Civil & Structural or Part-B Electrical or Part-C Mechanical (same branch as Paper-I) | 100 | 300 | 2 Hours |
Good to know: Questions come in Hindi and English. Candidates eligible for a scribe get 2 hours 40 minutes for each paper. The IS 456:2000 table and the Steam Table (where needed) are shown on screen, and an on-screen scientific calculator is available for the whole exam. No physical calculator or table is allowed inside the lab. The branch you chose in the application form cannot be changed.
SSC JE 2026 Negative Marking & Qualifying Marks
- Paper-I: 0.25 mark deducted for every wrong answer.
- Paper-II: 1 mark deducted for every wrong answer. Since Paper-II has 100 questions for 300 marks, each question works out to 3 marks, so a wrong guess costs you a third of a question.
- Minimum qualifying marks (both papers): UR 30%, OBC/EWS 25%, all other categories 20%.
- Paper-I is qualifying. Its normalized marks are used only to shortlist you, category-wise, for Paper-II.
- Final merit is based only on normalized Paper-II marks, plus your post preferences.
- Electrical vs Mechanical: Some posts are common to both branches, so SSC normalizes Electrical and Mechanical scores against each other.
- No re-checking: There is no re-evaluation of scores at any stage.
SSC JE 2026 Syllabus for Paper-I
General Intelligence and General Awareness are compulsory for everyone. The third section is your own branch.
General Intelligence & Reasoning: Verbal and non-verbal questions on analogies, similarities and differences, space visualization, problem solving, analysis, judgment, decision making, visual memory, discrimination, observation, relationship concepts, arithmetical reasoning, verbal and figure classification, arithmetical number series, abstract ideas and symbols, and arithmetical computations.
General Awareness: Your awareness of the world around you and current events, everyday science, and questions on India and its neighbouring countries, especially History, Culture, Geography, Economic Scene, General Polity and Scientific Research. No special study of any discipline is needed.
Part-A (Civil & Structural): Engineering Mechanics, Solid Mechanics, Structural Analysis, Construction Materials and Management, Estimating, Costing and Valuation, Concrete Structures, Steel Structures, Surveying, Soil Mechanics, Fluid Mechanics and Hydraulics, Hydrology and Irrigation, Environmental Engineering, Transportation (Traffic) Engineering.
Part-B (Electrical): Fundamentals of Electrical Engineering, Magnetic Circuits, A.C. Fundamentals, Measurement and Measuring Instruments, Electrical Machines, Special Electric Machines and Synchronous Generators, Generation, Transmission and Distribution, Estimation & Costing, Utilization of Electrical Energy, Basic Electronics, Power Electronics.
Part-C (Mechanical): Engineering Mechanics, Strength of Materials, Theory of Machines, Machine Design, Materials Science and Engineering, Thermal Engineering, Fluid Mechanics and Hydraulic Machinery, Industrial Engineering, Manufacturing Engineering, Metrology and Measurement, Advanced Manufacturing Processes.
SSC JE 2026 Syllabus for Paper-II: Civil Engineering
Paper-II covers the same branch subjects, but the notice spells out each one in detail. Here is the Civil list, topic by topic.
| Topic | What to Study |
|---|---|
| Engineering Mechanics | System of forces, free-body diagrams, equilibrium equations, internal forces in structures, friction, centre of mass, moment of inertia |
| Solid Mechanics | SF and BM in determinate beams, stress-strain, simple bending, flexural and shear stresses, torsion, column buckling, combined and direct bending stresses |
| Structural Analysis | Determinate and indeterminate structures, superposition, trusses, arches, beams, cables and frames, slope deflection, moment distribution, influence lines |
| Construction Materials & Management | Bricks, stones, timber, steel, cement, aggregates, plastics, polymers, glass, concrete, mix design and testing; project planning, PERT and CPM |
| Estimating, Costing & Valuation | Fundamentals of estimating, cost estimates, rate analysis, valuation, detailed estimates |
| Concrete Structures | Working stress and limit state concepts, design of beams, slabs, columns, foundations, retaining walls, bond and development length |
| Steel Structures | Working stress and limit state concepts, bolted connections, welds, tension and compression members, beams, plastic analysis |
| Surveying | Principles, errors, maps and scales, chain and compass, plane table, levelling, traversing, triangulation, total station, tacheometry, theodolite |
| Soil Mechanics | Phase relationships, index properties, soil classification, permeability, seepage and flow nets, effective stress, compaction, consolidation, shear strength, Mohr’s circle |
| Fluid Mechanics & Hydraulics | Fluid properties and statics, continuity, momentum and energy equations, laminar and turbulent flow, pipe networks, lift and drag, flow measurement, specific energy, hydraulic jump |
| Hydrology & Irrigation | Hydrologic cycle, infiltration, unit hydrographs, flood estimation, groundwater and Darcy’s law; irrigation methods, duty and delta, gravity dams, spillways, canals |
| Environmental Engineering | Water quality and treatment, distribution systems, sewerage design, wastewater treatment, sludge disposal, air pollution and AQI, municipal solid waste |
| Transportation Engineering | Highway geometric design, railway track speed and cant, pavement materials, flexible and rigid pavement design (IRC), traffic studies, Webster’s signal design, intersections, capacity |
SSC JE 2026 Syllabus for Paper-II: Electrical Engineering
| Topic | What to Study |
|---|---|
| Fundamentals | Resistors, capacitors, inductors, batteries; voltage, current, power, energy, flux and units; KCL, KVL, node and mesh analysis; Thevenin, Norton, superposition, maximum power transfer |
| Magnetic Circuits | Flux, reluctance, self and mutual inductance, MMF, magnetic circuits |
| A.C. Fundamentals | RMS and average values, series and parallel AC circuits, resonance, balanced three-phase circuits, star-delta, complex power, power factor |
| Measurements | Voltage, current, power and PF measurement, instrument types and errors, galvanometer, ammeter, voltmeter, wattmeter, Wheatstone and Kelvin’s double bridge, energy meter, megger, CT and PT |
| Electrical Machines | Single and three-phase transformers, DC machines, single and three-phase induction motors, starting, speed control, braking, torque-speed characteristics |
| Special Machines & Synchronous Generators | Fractional motors, servomotors, armature reaction, parallel operation, synchronization |
| Generation, Transmission & Distribution | Power stations, load, demand and diversity factors, PF improvement, line parameters, corona and Ferranti effect, circuit breakers, protection, cables |
| Estimation & Costing | Lighting schemes, electrical installation of machines, earthing practices and IE Rules |
| Utilization of Electrical Energy | Illumination, electric heating, welding, electroplating, traction and drives |
| Basic Electronics | PN junction diodes, rectifiers, clipping, clamping, BJT and FET, amplifiers, oscillators |
| Power Electronics | Thyristor V-I characteristics, firing circuits, buck, boost and buck-boost converters, half, full and midpoint controlled rectifiers |
SSC JE 2026 Syllabus for Paper-II: Mechanical Engineering
| Topic | What to Study |
|---|---|
| Engineering Mechanics | Free body diagrams, resultant of forces, Lami’s theorem, laws of friction, centroid and centre of gravity |
| Strength of Materials | Stress and strain, types of beams, SF and BM, bending and deflection, torsion of shafts, thin cylindrical shells |
| Theory of Machines | Cams, belt, chain, rope and gear drives, gear trains, flywheels, governors, balancing, vibration, brakes, dynamometers, clutches, bearings |
| Machine Design | Loads and stresses, creep and fatigue, theories of failure, cotter and knuckle joints, keys, shafts, couplings, spur gear, power screw, springs, bolted and welded joints |
| Materials Science | Crystal structure, iron-carbon diagram, heat treatment, cast iron and steels, non-ferrous alloys, material testing, NDT, corrosion |
| Thermal Engineering | Laws of thermodynamics, power plants, heat pump and refrigerator, steam generators, nozzles and turbines, IC engines (Otto, Diesel, Dual cycles), air compressors, refrigeration and AC, gas turbines, heat transfer, heat exchangers |
| Fluid Mechanics & Hydraulic Machinery | Fluid properties, flow through pipes, continuity equation, impact of jets, hydraulic turbines, centrifugal and reciprocating pumps |
| Industrial Engineering | Plant layout, work study, production planning and control, statistical quality control, inventory control |
| Manufacturing Engineering | Pattern making, moulding, casting, metal forming, gas, arc and resistance welding, lathe, broaching, drilling, milling, gear making, grinding, press working |
| Metrology & Measurement | Precision, accuracy, calibration, linear and angular measurement, comparators, surface finish, CMM, limits, fits and tolerances |
| Advanced Manufacturing | Jigs and fixtures, CNC machines, PLC, EDM, ECM, AJM, LBM, EBM, CAD/CAM basics, industrial robots, FMS |
Who writes which paper: Civil candidates attempt Part-A, Electrical candidates Part-B and Mechanical candidates Part-C, in both papers. As per the notice, candidates who opt for JE (Mechanical) are also eligible for JE (Electrical & Mechanical) posts. Exam centres for Telangana and Andhra Pradesh include Hyderabad, Karimnagar, Warangal, Siddipet, Vijayawada, Visakhapatnam, Guntur, Tirupathi, Kurnool and others under SSC Southern Region.
How to Prepare for SSC JE 2026
- Start with your diploma notes and standard textbooks. The level is diploma, so concepts matter more than tricky derivations.
- In Paper-II, a wrong answer costs 1 mark against 3 for a right one. Skip questions where you can’t narrow it down to two options.
- Civil aspirants should get comfortable reading IS 456:2000 tables on screen, since the table is provided during the exam.
- Take full-length mocks under a 2-hour timer and review every wrong answer the same day.
- Keep checking ssc.gov.in for Paper-I answer keys and the Paper-II schedule.
SSC JE 2026 SyllabusSSC JE Exam Pattern 2026SSC JE Civil SyllabusSSC JE Electrical SyllabusSSC JE Mechanical SyllabusSSC JE Paper 2 Syllabus
SSC JE 2026 Syllabus – Frequently Asked Questions
Are Paper-I marks counted in the SSC JE 2026 final merit?
No. Paper-I is qualifying. Final merit is prepared only on normalized Paper-II marks.
What is the negative marking in SSC JE 2026?
0.25 mark per wrong answer in Paper-I and 1 mark per wrong answer in Paper-II.
What level are the SSC JE engineering questions?
Approximately the level of a Diploma in Civil, Mechanical or Electrical Engineering, as per the official notice.
Is a calculator allowed in SSC JE 2026?
Only the on-screen scientific calculator. Physical calculators and printed tables are not allowed. IS 456:2000 and Steam Tables appear on screen when needed.
When is SSC JE 2026 Paper-I and Paper-II?
Paper-I is proposed on 2–6 November 2026 and 30 November–1 December 2026. Paper-II is tentatively in December 2026.
What are the minimum qualifying marks?
UR 30%, OBC/EWS 25% and all other categories 20%, in both Paper-I and Paper-II.
Quick Summary
| Exam | SSC Junior Engineer Examination, 2026 |
| Branches | Civil, Electrical, Mechanical (plus Telecom and IMD Scientific Assistant) |
| Tentative Vacancies | 1,699 (as on 08.10.2026) |
| Paper-I | 200 Q / 200 Marks / 2 Hours (qualifying) |
| Paper-II | 100 Q / 300 Marks / 2 Hours (decides merit) |
| Negative Marking | 0.25 (Paper-I), 1 mark (Paper-II) |
| Syllabus Level | Diploma in Engineering |
| Pay | Level-6, ₹35,400–1,12,400 |
| Official Website | ssc.gov.in |